In preparation for the Iowa Star Party I'm doing a some imaging housekeeping. The guider needs a fresh calibration and the filter offsets need a good redoing. More complicated are the changes needed for a basic imaging sequence using the Samyang lens. Because rotating the camera/lens requires the EAF belt to be disengaged and then re-engaged, one needs to put some breaks into the sequence to make opportunities for working with the belt. Here's what I'm setting up for the Iowa party.

The following instructions are for the NINA advanced sequencer. If you're not using that, you really should be! Also note that this is specific to a short focal length system for which you intend shoot RGB suitable for drizzle processing.

• NINA's Advanced Sequencer (If you are not, you should be)
• Your EAF position is zero when the lens focus is at the infinity stop

All good? Great. Here's what you need to do if you plan to orient the imagining camera while it sits in an Astrodymium cradle. It's a little complicated by the need to disengage the EAF belt while turning the lens.

Rotating the lens requires that you add two Message Box (MB) instructions to the sequence. The MB instruction is found in the Utility section. Obviously, if you don't care about the camera orientation, you can just skip the following.

If you're doing a Slew, Center, and Rotate (SCR) and have connected the Manual Rotator to NINA, place one MB just before the SCR command and another just after it. When the sequence reaches the first one, it will stop. You should then disengage the belt from the lens, being careful to not disturb the focus. Then click away the Message Box. NINA will slew, center, and tell you the amount and direction to rotate the lens. Do this until NINA is happy. It may also do some additional centering, but eventually it will reach the second MB and stop. Re-engage the focus belt. Verify that focus is good enough for autofocusing, and click away the second MB. The sequence will now resume normal operation.

If you're using Slew and Center (SC) and simply eyeballing the orientation, just use one MB immediately after the SC instruction and a second SC right after that*. When sequencer get to the MB, Disengage the EAF belt and manually orient the camera using snapshots. When the orientation is correct, re-engage the belt, check focus, and click away the MB.

*The second SC is needed to insure the target is at frame center; it acts as the post-rotation recentering performed by SCR but not by SC.

----------------------------------------------

I still wasn't happy with the tilt I was seeing, and I wondered if maybe it was coming from the way I had the camera attached to the Samyang -- that partially attached 5 mm spacer seemed iffy. I sent a note to Nic at ThinkableCreations asking if he had some advice about how to remove about 2 mm from the M42 threads on the adapter he sells. He didn't, but he expressed some concerns about the shorter thread length not providing a solid connection. I thought that would not be a problem and went ahead with my plan to sand off the end of the threads.

I used 600 Ultrafine "Wetordry" sandpaper from 3M for a while and made little progress, so I switched to 400 and it went nicely. Eventually I was able to attach my 7.5 mm spacer to the Thinkable adapter, giving me 45.5 mm of backfocus, close enough to the 45.0 desired.

Sounds good, but the reality was that this change once again made the lens unable to focus infinity.

Probably the 5 mm spacer wasn't quite sitting flush on the ThinkableCreations adapter (with the still-too-long M42 threads). I added two spacer shims to bring the back focus up to 44 mm. The focus position was now around 2300. One last tilt shim took it up to 44.2 mm 

 Evidently the ability of a lens to reach focus depends strongly on backfocus, something I didn't know.

Focuser position (vertical axis) vs. Backfocus (horizontal axis, mm)

(The zero position in the diagram corresponds to the maximum lens movement in the direction of infinity focus.)

The diagram suggests I could possibly add another half mm or so before running into focus issues, but I'll probably just leave it as is for now. I can tinker with it again next year.

----------------------------------------------

Anyway, here I am a few days away from the Iowa Star Party and I'm going to shove my perfectionist nature to the curb and settle for "good enough." I'm going to rely on BlurXTerminator to handle aberration and tilt issues.

Here's an idea of what the lens can do. This is about a 16th of the full image area, unscaled. M31 straddles the right edge of the image. This is a single 20 second frame of luminance; click to see it at 1:1 scale.